Aalco carries over 10,000 stock items covering a wide range of grades/alloys, shapes and sizes, and can cater for all your metal needs - from industry standards to special or bespoke items for particular applications or individual customers.
Aluminium alloy 6061 is a medium to high strength heat-treatable alloy with a strength higher than 6005A. It has very good corrosion resistance and very good weldability although reduced strength in the weld zone. It has medium fatigue strength. It has good cold formability in the temper T4, but limited formability in T6 temper. Not suitable for very complex cross sections.
Applications
Alloy 6061 is typically used for heavy duty structures in:
~ Rail coaches
~ Truck frames
~ Ship building
~ Bridges and Military bridges
~ Aerospace applications including helicopter rotor skins
~ Tube
~ Pylons and Towers
~ Transport
~ Boilermaking
~ Motorboats
~ Rivets
|
BS EN 573-3:2009 Alloy 6061 |
|
|---|---|
| Chemical Element | % Present |
| Aluminium (Al) | balance |
| Other (Each) | 0.05 max |
| Manganese (Mn) | 0.15 max |
| Titanium (Ti) | 0.15 max |
| Others (Total) | 0.15 max |
| Zinc (Zn) | 0.25 max |
| Chromium (Cr) | 0.04 - 0.35 |
| Copper (Cu) | 0.15 - 0.4 |
| Iron (Fe) | 0.7 max |
| Silicon (Si) | 0.4 - 0.8 |
| Magnesium (Mg) | 0.8 - 1.2 |
The most common temper for 6061 aluminium is:
Alloy 6061 is typically supplied as
| Physical Property | Value |
|---|---|
| Density | 2.70 g/cm³ |
| Thermal Expansion | 23.4 x10^-6 /K |
| Melting Point | 650 °C |
| Modulus of Elasticity | 70 GPa |
| Thermal Conductivity | 166 W/m.K |
| Electrical Resistivity | 0.040 x10^-6 Ω .m |
|
BS EN 755-2:2008 Extrusions - Up to 200mm Dia. & A/F, 5mm WT for Tube and Prof |
|
|---|---|
| Mechanical Property | Value |
| Proof Stress | 240 Min MPa |
| Tensile Strength | 260 Min MPa |
| Hardness Brinell | 95 HB |
Weldability – Gas: Good
Weldability – Arc: Very Good
Weldability – Resistance: Good
Brazability: Good
Solderability: Good
Workability – Cold: Good
Machinability: Acceptable
This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon.
Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.
The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed & online) and manufacturers' data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources.
Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards.
As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied.
Advice given by the Company to any third party is given for that party's assistance only and without liability on the part of the Company. All transactions are subject to the Company's current Conditions of Sale. The extent of the Company's liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.
