Aalco carries over 10,000 stock items covering a wide range of grades/alloys, shapes and sizes, and can cater for all your metal needs - from industry standards to special or bespoke items for particular applications or individual customers.
Stainless steel producers have an ongoing programme of development designed to produce new grades. These new grades are sometimes developed for specific end uses and sometimes to improve upon an existing grade.
Type 1.4510 spans both of these two areas since it was developed for a particular range of applications in certain industries where it can be used in place of type 1.4301 (304). On some aspects, its properties and performance in service are actually superior to 304 whilst on others it falls between 430 and 304. Notably however, it is also lower cost than 304.
Type 1.4509 can be referred to as a 'Super-Ferritic'
Features:
~ Good for Deep Drawing
~ Good Weldability
~ Good pitting corrosion resistance
~ Good brightness
~ Polishes well
Applications/Industries:
The main target sector is catering equipment to replace grade 304
Availability:
~ 1250mm & 1500mm wide
~ Thicknesses 0.5mm to 2.0mm
~ Finishes Bright Annealed or Polished
|
EN 10088-2:2005 1.4510 Steel |
|
|---|---|
| Chemical Element | % Present |
| Iron (Fe) | balance |
| Sulphur (S) | 0.02 max |
| Phosphorous (P) | 0.04 max |
| Carbon (C) | 0.05 max |
| Titanium (Ti) | 0.5 - 0.8 |
| Manganese (Mn) | 1 max |
| Silicon (Si) | 1 max |
| Chromium (Cr) | 16 - 18 |
Stainless Steel Grade 1.4510 is similar to, but may not be a direct equivalent to:
Type 439
UNS S43035
Uginox F18TNb
Sometimes referred to as 430LX.
| Physical Property | Value |
|---|---|
| Density | 7.70 g/cm³ |
| Melting Point | 1505 °C |
| Thermal Expansion | 11.0 x10^-6 /K |
| Modulus of Elasticity | 220 GPa |
| Thermal Conductivity | 25.0 W/m.K |
| Electrical Resistivity | 0.60 x10^-6 Ω .m |
|
EN 10088-2:2005 Sheet & Plate - Up to 13.5mm Thick |
|
|---|---|
| Mechanical Property | Value |
| Proof Stress | 230 Min MPa |
| Tensile Strength | 420-600 MPa |
| Elongation A50 mm | 23 Min % |
This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon.
Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.
The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed & online) and manufacturers' data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources.
Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards.
As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied.
Advice given by the Company to any third party is given for that party's assistance only and without liability on the part of the Company. All transactions are subject to the Company's current Conditions of Sale. The extent of the Company's liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.
